Home
Check out the Zoeller YouTube Channel for tips, training, and product videos!
X
6180 Series
6180 Series
Application- Commercial Buildings
0.5 or 1 HP Effluent or dewatering submersible pumps, 1.5”, 2” or 3” NPT vertical discharge
-
Features and Benefits
- Durable, epoxy coated cast iron construction
- Motor : 1 Ph or 3 Ph, oil-filled, hermetically-sealed, automatic reset, thermal overload protected (1 Ph)
- Bearings – Upper and lower ball bearings
- Stainless steel motor shaft
- Dual mechanical shaft seals – upper carbon/ceramic, lower silicon carbide/carbon. Optional seal materials available
- Viton O-ring seals and cover gasket
- Impeller – non-clogging, cast iron vortex design passes 3/4″ (19 mm) spherical solids
- 25′ (8 m), UL listed, 3-wire neoprene cord and plug. Longer cords available in lengths of 35′ – 50′ (11 m – 15 m)
- No screens to clog
- Stainless steel screws, bolts and handle
- 1-1/2″ NPT discharge with 2″ or 3″ flange available
- Corrosion-resistant, powder coated epoxy finish
- Moisture sensors available for early warning of seal failure (optional)
- 100% computerized tested
-
Product Specifications
Voltage Ability 200 / 230 / 460 / 575 Phase 1 & 3 Hz 60 Discharge Size 1.5″ Standard, 2″ & 3″ Optional Solids Handling 3/4″ HP 1/2 & 1 RPM 3450 Seals Upper – Carbon Ceramic
Lower – Silicon Carbide/CarbonO Rings Viton Impeller Cast Iron Vortex -
Technical Data
CAUTION
All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).
SELECTION GUIDE
- Single or double piggyback variable level float switch pump control using the 15 amp plug and receptacle. Refer to ZM1536.
- Single piggyback variable level float switch, hard wiring the pump lead wires to the float switch leads.
- Refer to ZM3376 and select the correct simplex control panel listed for the pump. Refer to ZM1536 and select the desired variable level control switch, 3 required.
- Refer to ZM3376 and select the correct duplex control panel listed for the pump. Refer to ZM1536 and select the desired variable level control switch, 3 or 4 required.
Pump Performance Curves
Design Tools
- Literature
- Durable, epoxy coated cast iron construction
- Motor : 1 Ph or 3 Ph, oil-filled, hermetically-sealed, automatic reset, thermal overload protected (1 Ph)
- Bearings – Upper and lower ball bearings
- Stainless steel motor shaft
- Dual mechanical shaft seals – upper carbon/ceramic, lower silicon carbide/carbon. Optional seal materials available
- Viton O-ring seals and cover gasket
- Impeller – non-clogging, cast iron vortex design passes 3/4″ (19 mm) spherical solids
- 25′ (8 m), UL listed, 3-wire neoprene cord and plug. Longer cords available in lengths of 35′ – 50′ (11 m – 15 m)
- No screens to clog
- Stainless steel screws, bolts and handle
- 1-1/2″ NPT discharge with 2″ or 3″ flange available
- Corrosion-resistant, powder coated epoxy finish
- Moisture sensors available for early warning of seal failure (optional)
- 100% computerized tested
| Voltage Ability | 200 / 230 / 460 / 575 |
| Phase | 1 & 3 |
| Hz | 60 |
| Discharge Size | 1.5″ Standard, 2″ & 3″ Optional |
| Solids Handling | 3/4″ |
| HP | 1/2 & 1 |
| RPM | 3450 |
| Seals | Upper – Carbon Ceramic Lower – Silicon Carbide/Carbon |
| O Rings | Viton |
| Impeller | Cast Iron Vortex |
CAUTION
All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).
SELECTION GUIDE
- Single or double piggyback variable level float switch pump control using the 15 amp plug and receptacle. Refer to ZM1536.
- Single piggyback variable level float switch, hard wiring the pump lead wires to the float switch leads.
- Refer to ZM3376 and select the correct simplex control panel listed for the pump. Refer to ZM1536 and select the desired variable level control switch, 3 required.
- Refer to ZM3376 and select the correct duplex control panel listed for the pump. Refer to ZM1536 and select the desired variable level control switch, 3 or 4 required.
English 
Spanish 
French 
Chinese(Asia) 
Chinese (China)